Palm Springs, CA

Performed annual maintenance in cooling on a reem package unit location roof top followed Sequence of operation Changed filter checked amps voltage capacitor temperature split working at range checked inrush was high installed compressor savor cleared condensation line cleared coils unit is working to manufacture specification in cooling at this time of visit

Performed annual maintenance in cooling on a Bosch platinum, followed sequence of operation Changed filter checked amps voltage temperature split working at range cleared condensation line rinsed coil down unit is working to manufacture specification in cooling at this time of visit

Performed annual maintenance in cooling on a American standard platinum, followed Sequence of operation Changed filter checked amps voltage pressures at CDA working at range cleared condensation line rinsed condenser down unit is working to manufacture specification in cooling at this time of visit

Moved can to line up and install (2) exhaust fans and kitchen hood vent.

Performed monthly maintenance in cooling on a 2015 American standard split condenser, followed Sequence of operation rinsed out filter checked amps voltage capacitor pressures working at range checked inrush was high installed compressor savor cleared condensation line rinsed condenser down unit is working to manufacture specification in cooling

Performed annual maintenance in cooling on a 5 ton amana condenser, followed Sequence of operation Changed filter checked amps voltage capacitor working at range checked pressures where low added 5 pounds of 410@ recommend leak surge did send estimate cleared condensation line rinsed condenser down unit is working to manufacture specification in cooling did send estimate for replacement

Performed annual maintenance in cooling on a 2019 4 ton train condenser. Followed sequence of operation filter was clean checked amps voltage capacitor working at range checked inrush was high installed compressor savor checked pressures where low balanced out sub cooling cleared condensation line rinsed condenser down also installed water safety switch to avoid any water damage and Jones valve to clear condensation line unit is working to manufacture specification in cooling at this time of visit

2020 Performed a semi annual cooling service on American Standard split heat/POV. Cycle equipment followed cooling sequence of operation check refrigerant/temperature split checked amps and voltage. 1050 thermostat checked out OK. Cleared condensation line. Replaced 20 x 25 filter located within the air handler/hallway, mechanical closet. Rinse condenser coil. Cooling equipment checked out operational at this visit.

Performed annual AC maintenance on two 2019 American standard split systems FAU located in garage and outside closet. Changed 16 x 25 and two 20 x 25 filters. Checked amps, volts, capacitor, and cleaned electrical compartment. Checked refrigerant levels, superheat, subcool and temperature split. Cleared lines and cleaned coils. Bolt systems have several issues that could cause breakdown in the near future. Living room/kitchen unit serial number 7J2F startup amps are rated for 153 and is pulling 176 A capacitor is rated for 40 and is reading 37 which is the minimal manufactured rating. Also condenser fan motor is operating at max rated amps. Bedroom unit serial number 7R2F startup amps are rated for 83 and is pulling 103.4 startup amps capacitor is rated for 40 and is also reading 37 bedroom unit condenser fan motor is rated for .71 A and is operating at .69. I have put together an email to estimate.

Comfort ac service on (2)2020 American standard heat pumps. Fau located outside closet and garage. Condensers located on north and south side of home. Replaced filters, flushed condensation lines and washed condenser coils. Checked all ac components and refrigerant levels.

Comfort ac service on (2)2015 Bryant split systems. Fau located inside closets, condensers on south side of home. Client had replaced filters. Condensation lines have pumps. Checked all ac components and refrigerant levels. Hard start kits working. Washed condenser coils. Renewed on yearly agreement.

Comfort ac service on 2016 Lennox platinum split system. Fau located inside closet, condenser on east side of home. Checked all ac components and refrigerant levels. Replaced filter, flushed condensation line and washed condenser coils. System properly running to manufacture specifications.

Performed annual cooling maintenance on a 2014 Lennox 4ton XC25 split system. Upflow FAU located in garage. Replaced customer supplied media filter. Followed sequence of operations and checked voltage, amperage, temperature split, Freon levels, serviced ductless unit, and rinsed condenser coils. Everything checked out in range. Removed programming for Lennox thermostat per clients request. Thermostat checked out operational. System is working properly in cooling at this time of service. Client renewed HFCC paid via CC.

Replaced stack switch in the kitchen that controls the light over the sink and the back patio lights

Quoted on a American Standard

Cooling service 2024 American standard equipment. Verified sequence of operation is working properly according to manufacturer specifications. Cleared drain lines, replaced filters, washed outdoor coils. Verified electrical compartments are clean and connections are secure.

Executed a cooling maintenance on a split system (technician notes). Cleared condensate drain line and replace filter. Refrigerant circuit diagnostic – good. Capacitor – good. Thermostat – good. Running and starting amperage measured within manufacture specifications on all motors. System is cooling the home at the time of maintenance.

Performed annual maintenance in cooling on a 5 ton American standard split, followed sequence of operation Changed filter location fau outside closet, checked amps voltage capacitor pressures working at range checked inrush was a little high installed compressor savor cleared condensation line rinsed condenser down unit is working to manufacture specification in cooling at this time of visit also installed surge protectors

Igniter wire accidentally disconnected when installing part last week. Reconnected and tested operation.

Came to property for panel inspection provided customer with quote to change out single pole breaker to a twin pole breaker.

Replaced 3/8”brass push in coupling at indoor section liquid line. Pressure tested to 300psig and checked new fitting and double checked all other fittings and coil, both couplings on both refrigerant lines are leaking significantly. Informed homeowner we will need to come back and will have to braze the refrigerant lines. Will follow up tomorrow morning before any calls 7:30-8 and get with office and homeowner to schedule new repair time and revised quote as it is now a larger repair/labor/supplies required.

Applied and disconnected voltage for reversing valve until unit switches right away to cooling. Refrigerant numbers and temperature split indicate proper cooling to manufacture specifications. Informed tenant to leave on cool (not off or heating mode) and to just raise temperature when they want unit off for time being . Tested turning unit on again and went right into cool mode.

Check cooling and electrical components found system low on refrigerant talk to Scott decline adding refrigerant to unit talk about replacing system sent options

We installed a high-efficiency 2-ton 18 SEER Mitsubishi system in the garage, which includes both an outdoor and indoor unit. The outdoor unit was securely placed on a pad and the indoor unit was installed in the garage. Refrigeration lines were carefully run in the garage, fully covered for aesthetic and protective purposes. Additionally, we connected the system to the main electrical panel using a dedicated 20/15 Eaton quad breaker.

Replaced blower motor under warranty unit is up and running